Probes And Senders
GRT CHT Bayonet Style Probe
Bayonet-style CHT probe. Used mostly with Lycoming and Continental engines.
Fuel Probe Mount Kit Hard Tank
Hard tank fuel probe mount kit.Dimensions: 2X4X4
Flight Data OAT Probe For GT50
Flight data OAT probe for GT-50. Note: This is the OAT probe for the newer GT-50 G-Meter Gauge only.Dimensions: .25X5.5X8
J.P. Instruments Option Compressor Probe Cdt
The Compressor Discharge Temperature (CDT) probe, is installed just after after the inter-cooler. The probe is installed with a #40 stainless stee...
View full detailsMGL EGT Thermocouple Clmp Sml
MGL Avionics Type-K EGT Thermocouple Clamp - Type small. 1.5 Dia. Probe dia. approx 0.198"Dimensions: .5X3.5X6.5
IM-932N CHT J Type Sender Ungrounded 3 Meters Max Temp 250C
IM-932N CHT J Type Sender Ungrounded 3 Meters Max Temp 250C
GRT Manifold Pressure Sensor 10-51 In Hg Map-02
GRT Manifold Pressure Sensor 10-51 In Hg Map-02
J.P. Instruments Option EDM TIT Probe With Shield And Ext Wire M111T TSO
The Turbine Inlet temperature (TIT) probe, is installed in the exhaust stack accumulator to a maximum depth of 1/2 inches and approximately 2-4 in...
View full detailsItc Replacement Gasket For Cessna S2670-1
ITC 13-10017-507 gasket used with Rochester fuel senders 7740 series. Cessna P/N S2670-1. Part 15-716 and 0015-00716 has been replaced by S2670-1....
View full detailsGarmin Carburetor AIR Temperature Probe 494-70010-00
Garmin Carburetor Air Temperature Probe 494-70010-00 NOTES: Ungrounded probe.
Fuel Pressure Sensor
The Fuel Pressure Sensor inserts into any 1/8 or ¼ NPT fitting in a fuel tank. It detects differential pressure between 0 and 1.5 bars of press...
View full detailsDavtron PROBE-7FT-RB Temp Probe 7FT Red/Blk Twisted (Analog) 301303307& 655
This probe is for 655, 301, 307, 303, 803 Length: 1.3" Diameter. .255" 7' Cale Probe is an active componet whe...
View full details86317 Alcor Ungrounded EGT / TIT Clamp Probe Type K
ALCOR 3-1/4 INCH CLAMP EGT/TIT PROBE WITH PLUG UNGROUNDED, .8 OHM, TYPE K Dimensions: 1X3.5X5.5
86317 Alcor Ungrounded EGT / TIT Clamp Probe Type K
ALCOR 3-1/4 INCH CLAMP EGT/TIT PROBE WITH PLUG UNGROUNDED, .8 OHM, TYPE K Dimensions: 1X3.5X5.5
Mitchell Pres Sender 100 PSI
Gauge Range: 100 PSI # Terminals: 1 Note: Units with one terminal require the mount be grounded. Dimensions: .175X1.75X3.125
Mitchell Presure Sender 80 PSI
Gauge Range: 80 PSI # Terminals: 1 Note: Units with one terminal require the mount be grounded. Dimensions: 2X2X3.25
MCI Carb Temp Probe B-5
Probe fits pretapped hole in Marvel-Schebler and Bendix carburetors Designed and built in Wichita, Kansas, USA One year limited warranty Dimensi...
View full detailsFuel Probe 12V 12IN 5BND
The probe is constructed of concentric tubing (a small tube inside a larger tube). The tubes, which are separated by small insulators to keep the...
View full detailsSwift 12MM CHT Sender
Swift CHT sender, 12mm dia. ring, 4ft metal shield wire. Similar to Falcon Gauge Made in China Dimensions: 1X4X4
JPI EDM Option OIL Press Sender With Harness
JPI EDM option, oil press sender with harness.Dimensions: 2X2X3.5
Mitchell Temp Sender 5/8 250F
Mitchell temperature sender 5/8 - 18 UNF Thread 250F degrees (FAA/PMA).Dimensions: .75X2.25X2.75
Westach Fuel Sender AP-H6-D120-5V
Capacitance fuel level sender 6", may be cut to 3", 1/4" OD, 12/24 vdc (28v max) input, 0-5 vdc output, non-bendable, 4 wires Made i...
View full details